A brief check of their site shows they use aluminum salts.
- 1 Post
- 42 Comments
Ive been using schmitts, but it’s baking soda based just like that old spice probably is. I really loved using sweet pitti, which is unscented and uses mandelic acid. Imo, mandelic acid is the king of deodorants. Nothing is going to stop the sweat except aluminum though.
BingoBangoBongo@midwest.socialto Asklemmy@lemmy.ml•What has been your best financial move in life?English2·1 year agoBig brain move.
BingoBangoBongo@midwest.socialOPto 3D Printing@lemmy.ml•Why does filament not stick to the glass?English1·1 year agoI was able to get it printing, but doing some calibration confirms that adjusting z offset made the bottom layer better. What’s the point in z offset specifically, vs just changing the gap when tramming or the initial layer height?
BingoBangoBongo@midwest.socialOPto 3D Printing@lemmy.ml•Why does filament not stick to the glass?English2·1 year agoIncrease in temp seemed to help!
BingoBangoBongo@midwest.socialOPto 3D Printing@lemmy.ml•Why does filament not stick to the glass?English2·1 year agoThis was the brim printing. But increasing temp did seem to help!
BingoBangoBongo@midwest.socialOPto 3D Printing@lemmy.ml•Why does filament not stick to the glass?English1·1 year agoThis is a really interesting idea! Ill give it a try.
BingoBangoBongo@midwest.socialOPto 3D Printing@lemmy.ml•Why does filament not stick to the glass?English3·1 year agoIncreasing temp by 5, plus recleaning the bed, plus doing some cold pulls helped a bit. I’ve always had issues getting things to stick at 60 for some reason, at least ever since I went to borosilicate. I’ll try adding more squish, since I have to dehydrate my filament before I give the print another shot.
BingoBangoBongo@midwest.socialOPto 3D Printing@lemmy.ml•Why does filament not stick to the glass?English3·1 year agoI’m ashamed to say, I do z offset by just tramming with a feeler gauge to adjust. I believe my initial layer is .2mm and I trammed it to.05mm and it smooshed too much, and still peeled up. .07mm was much to tall, and this was at .06mm. I finally got the print working after doing some more cold pulls and recleaning the glass a little better.
BingoBangoBongo@midwest.socialOPto 3D Printing@lemmy.ml•Why does filament not stick to the glass?English2·1 year agoIt is borosilicate, which is a decision I’ve come to regret. Using hair spray and glue sticks works, but is so messy to clean
BingoBangoBongo@midwest.socialOPto 3D Printing@lemmy.ml•Why does filament not stick to the glass?English1·1 year agoYeah I was doing that for a bit but I hate cleaning it off the plate. I should have never switched to borosilicate 😂
BingoBangoBongo@midwest.socialto World News@beehaw.org•Greenland startup begins shipping glacier ice to cocktail bars in the UAEEnglish4·1 year agoAnd this is something that actually makes sense.
Originated with a face book page “the ol’ ghost of dale earnhardt” supposedly. Some guy trying to turn dale into a progressive icon.
BingoBangoBongo@midwest.socialto Gaming@lemmy.ml•I banned my kid from Roblox.... what next?English3·1 year agoThe finals is also only voice chat and its opt in from the get go, so really good for avoiding toxic behavior from randos
BingoBangoBongo@midwest.socialto Memes@lemmy.ml•Your mix tape isn't fire, it's smouldering at bestEnglish4·1 year agoI was gonna say that. The guy with the speaker is also the one asking you for coke or heroin on the L.
Wow I stand corrected
They are, because the president can nominate, but the legislature has to confirm.
Yeah I’m sure it is endemic at this point, but it’s still killing 100 Americans a day. I don’t think the flu is near that level, but I could be mistaken. Vaccines are still crucial against both.
Source: https://www.worldometers.info/coronavirus/country/us/
Edit: I’m wrong, they are at nearly identical mortality rates.
They just repealed right to work in Michigan, and Meijer employees presumably used that leverage to significantly improve wages and benefits.